空调移机怎么回收氟利昂？空调移机注意什么

How to recycle Freon when the air conditioner is moved? What should we pay attention to when moving the air conditioner

空调移机怎么回收氟利昂？

How to recycle Freon when the air conditioner is moved?

A、将空调调制到制冷状态下：首先使用扳手将室外机两个连接管阀门的盖子给打开，然后需要使用5个的六角扳手，将其放到细的（高压阀）阀口，然后再阀门迅速的关上，大概20秒过去之后再将粗的阀门（低压）关上，然后才是关闭空调电源，断掉电源。这样做完之后就将氟收到外机中去了。这样就能够进行拆机工作了。

A. Modulate the air conditioning to refrigeration state: first, open the lid of the two connecting pipe valves of the outdoor machine with a wrench, and then use five hexagonal wrenches to place it at the fine (high-pressure) valve opening. Then the valve closes quickly. After about 20 seconds, turn off the thick (low-pressure) valve, and then turn off the air conditioning power supply. After doing this, fluorine is received into the external machine. In this way, the machine can be disassembled.

B、安装的时候还有开阀门排空：具体如下：把内外机固定好之后，把空调连接好，主要是把内外机连接管都紧好，注意一定接好，以防制冷剂泄露。

B. When installing, there are also valves to empty: Specifically as follows: after fixing the internal and external machine, connect the air conditioner well, mainly tighten the connecting pipe of the internal and external machine, pay attention to certain connection, in order to prevent the leakage of refrigerant.

C．开关打到自动档空调就正常工作，用内六角打开高压阀门（细管阀门），再用六角顶住加氟口顶针（加氟口在低压上），使里面的气体跑出来，10秒钟左右就可以了，不要时间太长，以免雪种跑的太多。这样就可以使管路里面的空气放出来。

C. Switch to automatic gear air-conditioning work normally, with the inner hexagonal open high-pressure valve (pipe valve), and then use hexagonal against the fluoride Jack needle (fluoride jack at low pressure), so that the gas inside can run out, about 10 seconds, do not take too long, so as not run too much snow. In this way, the air in the pipeline can be released.

D．然后把高低压的阀门都打开，接上内外机的电源线就可以了。注意：连接管是铜的，不能盘成死弯，否则就会影响制冷剂的流动，造成不能制冷和制热。拆的时候要先收氟，否则就会造成氟的泄露。

D. Then open the high and low pressure valves and connect the power cord of the internal and external machine. Note: The connecting pipe is copper and can not be coiled into a dead bend. Otherwise, it will affect the flow of refrigerant, resulting in the failure of refrigeration and heating. When dismantling, fluorine should be collected first, otherwise it will cause fluorine leakage.

空调移机注意什么？

What should I pay attention to when moving the air conditioner?

A、测试空调器在移机前各项功能工作是否正常。回收制冷剂，拆除室内外连接线。好能在连接线两端做好标记，就不至于在装机时出现将连接线接错引起故障的可能。

A. Testing whether the functions of air conditioner are normal before moving. Recycle refrigerant and remove indoor and www.jubenban.net.cnwww.jianchajingmujuz.cnwww.chuqiji.com.cnwww.huanyangshuzhii.cn

www.qiegejii.cn www.xiaoyuandiaosu.net.cn outdoor connections. Good marking at both ends of the connection line can avoid the possibility of faults caused by wrong connection of the connection line during installation.

B、在外机搬运、安装过程中，不能翻转，倾斜角太大，切忌用手抓截止阀抬机。

B. In the process of handling and installing the external machine, it should not be turned over, and the inclination angle is too large. Do not lift the machine by grasping the globe valve by hand.

C、接线端子或其他有接线的地方是否有松动的现象，防止出现打火或其他隐患的发生，电线是否有老化的现象，如有老化的一定要如以更换。

C. Are there loosening phenomena at terminals or other places where there are connections to prevent the occurrence of fire or other hidden dangers, and whether there is aging phenomena in wires, if there is aging, it must be replaced.

D、老式空调器停机后不可在3分内重新开机，否则容易烧坏压缩机。新式空调安有防止3分内重新开机的电路，即使在3分内重开机，压缩机也不工作。

D. Old air conditioners should not be restarted within 3 minutes after shutdown, otherwise the compressor will burn out easily. The new air conditioner has a circuit to prevent restarting within 3 minutes, even if restarting within 3 minutes, the compressor does not work.

E、装修过程中有时因为房子空间结构的改变，发现家里空调安装的位置需要调整一下，这时我们就需要空调移机，空调移机我们要做好空调新的移机位置，打好孔，拉好电线等，我们可以通过设计师量房预留好家电安装的位置。

E. In the process of renovation, sometimes because of the change of the space structure of the house, we find that the location of the air conditioning installation needs to be adjusted. At this time, we need to move the air conditioner. We need to do a good job of the new location of the air conditioner, punch holes, pull wires and so on. We can reserve the location of the household appliances installation through the designer's measuring room.